#include <CSCRecHitDBuilder.h>

Public Member Functions
void	build (const CSCStripDigiCollection stripds, const CSCWireDigiCollection wireds, CSCRecHit2DCollection &oc)

	CSCRecHitDBuilder (const edm::ParameterSet &ps)

const CSCLayer *	getLayer (const CSCDetId &detId)

void	setConditions (CSCRecoConditions *reco)

void	setGeometry (const CSCGeometry *geom)

	~CSCRecHitDBuilder ()

Private Attributes
const CSCGeometry *	geom_

CSCHitFromStripOnly *	hitsFromStripOnly_

CSCHitFromWireOnly *	hitsFromWireOnly_

CSCMake2DRecHit *	make2DHits_

bool	makePseudo2DHits

CSCRecoConditions *	recoConditions_

int	stripWireDeltaT

bool	useCalib

Detailed Description

Algorithm to build 2-D RecHit from wire and strip digis in endcap muon CSCs by implementing a 'build' function required by CSCRecHitDProducer.

The builder goes through many stages before building 2-D hits: 1) It finds wire clusters and form wire hits which it stores in CSCWireHit. 2) From these wire hits, it builds pseudo-wire segments to clean up the wire hit collection from noisy hits. Only the hits falling on the segment or far away from existing segments are retained. 1) It then finds strip cluster and hits which it stores in CSCStripHit. 2) Similary to the wire hits, segments are build using the strip hits. Because of the trapezoidal geometry of the strips, all strip hits falling close to the pseudo-strip segments are retained.

Author: Stoyan Stoynev - NU

Definition at line 39 of file CSCRecHitDBuilder.h.

Constructor & Destructor Documentation

CSCRecHitDBuilder::CSCRecHitDBuilder ( const edm::ParameterSet & ps )

explicit

Configure the algorithm via ctor. Receives ParameterSet percolated down from EDProducer which owns this Builder.

Definition at line 30 of file CSCRecHitDBuilder.cc.

References edm::ParameterSet::getParameter(), hitsFromStripOnly_, hitsFromWireOnly_, make2DHits_, stripWireDeltaT, and useCalib.

                                                                 : geom_(nullptr) {
   
   // Receives ParameterSet percolated down from EDProducer  
 
   useCalib               = ps.getParameter<bool>("CSCUseCalibrations");  
   stripWireDeltaT        = ps.getParameter<int>("CSCstripWireDeltaTime");
   
   hitsFromStripOnly_     = new CSCHitFromStripOnly( ps ); 
   hitsFromWireOnly_      = new CSCHitFromWireOnly( ps );  
   make2DHits_            = new CSCMake2DRecHit( ps );
 }

CSCRecHitDBuilder::~CSCRecHitDBuilder ( )

Definition at line 43 of file CSCRecHitDBuilder.cc.

References hitsFromStripOnly_, hitsFromWireOnly_, and make2DHits_.

                                       {
   delete hitsFromStripOnly_;
   delete hitsFromWireOnly_;
   delete make2DHits_;   
 }

Member Function Documentation

void CSCRecHitDBuilder::build	(	const CSCStripDigiCollection *	stripds,
		const CSCWireDigiCollection *	wireds,
		CSCRecHit2DCollection &	oc
	)

Find digis in each CSCLayer, build strip and wire proto-hits in each layer from which pseudo-segments are build to select hits. Then, strip/wire hits are combined to form 2-D hits, whereas remaining "good" strip and wire only hits are also stored into output collection.

Definition at line 50 of file CSCRecHitDBuilder.cc.

References relativeConstraints::chamber, CSCDetId::chamber(), CSCDetId::endcap(), makeMuonMisalignmentScenario::endcap, Exception, CSCRecoConditions::fillBadChannelWords(), geom_, getLayer(), CSCMake2DRecHit::hitFromStripAndWire(), hitsFromStripOnly_, hitsFromWireOnly_, triggerObjects_cff::id, CSCMake2DRecHit::isHitInFiducial(), CSCDetId::layer(), LogTrace, make2DHits_, recoConditions_, CSCDetId::ring(), CSCHitFromStripOnly::runStrip(), CSCHitFromWireOnly::runWire(), and CSCDetId::station().

Referenced by CSCRecHitDProducer::produce().

                                                            {
   LogTrace("CSCRecHitDBuilder") << "[CSCRecHitDBuilder] build entered";
 
   if ( !geom_ ) throw cms::Exception("MissingGeometry") << "[CSCRecHitDBuilder::getLayer] Missing geometry" << std::endl;
 
 
 
 
   //  create 2-D hits by looking at superposition of strip and wire hit in a layer
   //
   // N.B.  I've sorted the hits from layer 1-6 always, so can test if there are "holes", 
   // that is layers without hits for a given chamber.
 
   // Vector to store rechit within layer
   std::vector<CSCRecHit2D> hitsInLayer;
 
   int layer_idx     = 0;
   int hits_in_layer = 0;
   CSCDetId old_id; 
 
   
   for ( CSCStripDigiCollection::DigiRangeIterator it = stripdc->begin(); it != stripdc->end(); ++it ){
     const CSCDetId& id = (*it).first;
     const CSCLayer* layer = getLayer( id );
     const CSCStripDigiCollection::Range& rstripd = (*it).second;
     
     // Skip if no strip digis in this layer
     if ( rstripd.second == rstripd.first ) continue;
 
     const CSCDetId& sDetId = id;
  
     // This is used to test for gaps in layers and needs to be initialized here 
     if ( layer_idx == 0 ) {
       old_id = sDetId;
     }
 
 
     CSCDetId compId = sDetId;
     CSCWireDigiCollection::Range rwired = wiredc->get( sDetId );
     // Skip if no wire digis in this layer
     // But for ME11, real wire digis are labelled as belonging to ME1b, so that's where ME1a must look
     // (We try ME1a - above - anyway, because simulated wire digis are labelled as ME1a.)
     if ( rwired.second == rwired.first ) {
       if ( sDetId.station()!=1 || sDetId.ring()!=4 ){
         continue; // not ME1a, skip to next layer
       }
       // So if ME1a has no wire digis (always the case for data) make the
       // wire digi ID point to ME1b. This is what is compared to the
       // strip digi ID below (and not used anywhere else). 
       // Later, rechits use the strip digi ID for construction.
       
       // It is ME1a but no wire digis there, so try ME1b...
       int endcap  = sDetId.endcap();
       int chamber = sDetId.chamber();
       int layer   = sDetId.layer();
       CSCDetId idw( endcap, 1, 1, chamber, layer ); // Set idw to same layer in ME1b
       compId = idw;
       rwired = wiredc->get( compId );
     }
  
     // Fill bad channel bitsets for this layer
     recoConditions_->fillBadChannelWords( id );
     
     // Build strip hits for this layer
     std::vector<CSCStripHit> const & cscStripHit = hitsFromStripOnly_->runStrip( id, layer, rstripd);
 
     if (cscStripHit.empty()) continue;
 
     hitsInLayer.clear();
     hits_in_layer = 0;
  
    
     // now build collection of wire only hits !  
     std::vector<CSCWireHit> const & cscWireHit = hitsFromWireOnly_->runWire(compId, layer, rwired);
 
    
     
     // Build 2D hit for all possible strip-wire pairs 
     // overlapping within this layer
     
     LogTrace("CSCRecHitBuilder")<< "[CSCRecHitDBuilder] found " << cscStripHit.size() << " strip and " 
                 << cscWireHit.size()  << " wire hits in layer " << sDetId;
     
     for (auto const & s_hit : cscStripHit) {
       for (auto const & w_hit : cscWireHit) {
     CSCRecHit2D rechit = make2DHits_->hitFromStripAndWire(sDetId, layer, w_hit, s_hit);
     
     bool isInFiducial = make2DHits_->isHitInFiducial( layer, rechit );
     if ( isInFiducial ) {
       hitsInLayer.push_back( rechit );
       hits_in_layer++;
     }
       }
     }
 
   
   
 
     LogTrace("CSCRecHitDBuilder") << "[CSCRecHitDBuilder] " << hits_in_layer << " rechits found in layer " << sDetId;
     // std::cout << "[CSCRecHitDBuilder] " << hits_in_layer << " rechits found in layer " << sDetId << std::endl;
     
     // output vector of 2D rechits to collection
     if (hits_in_layer > 0) {
       oc.put( sDetId, hitsInLayer.begin(), hitsInLayer.end() );
       hitsInLayer.clear();
     }
     hits_in_layer = 0;
     layer_idx++;
     old_id = sDetId;
   }
 
   LogTrace("CSCRecHitDBuilder") << "[CSCRecHitDBuilder] " << oc.size() << " 2d rechits created in this event.";
 
 }

const CSCLayer * CSCRecHitDBuilder::getLayer ( const CSCDetId & detId )

Definition at line 167 of file CSCRecHitDBuilder.cc.

References geom_, and CSCGeometry::layer().

Referenced by build(), and setGeometry().

                                                                     {
   return geom_->layer(detId);
 }

void CSCRecHitDBuilder::setConditions ( CSCRecoConditions * reco )

Pass conditions downstream

Definition at line 172 of file CSCRecHitDBuilder.cc.

References hitsFromStripOnly_, hitsFromWireOnly_, make2DHits_, trackingPlots::reco, recoConditions_, CSCMake2DRecHit::setConditions(), CSCHitFromStripOnly::setConditions(), and CSCHitFromWireOnly::setConditions().

Referenced by CSCRecHitDProducer::CSCRecHitDProducer(), and setGeometry().

                                                                {
   recoConditions_ = reco;
   hitsFromStripOnly_->setConditions( reco );
   hitsFromWireOnly_->setConditions( reco );
   make2DHits_->setConditions( reco );  
 }

void CSCRecHitDBuilder::setGeometry ( const CSCGeometry * geom )

inline

Cache pointer to geometry so it can be passed downstream

Definition at line 65 of file CSCRecHitDBuilder.h.

References relativeConstraints::geom, geom_, getLayer(), and setConditions().

Referenced by CSCRecHitDProducer::produce().

65 {geom_ = geom;}

CSCRecHitDBuilder::geom_

const CSCGeometry * geom_

Definition: CSCRecHitDBuilder.h:94

relativeConstraints.geom

geom

Definition: relativeConstraints.py:72

Member Data Documentation

const CSCGeometry* CSCRecHitDBuilder::geom_

private

Definition at line 94 of file CSCRecHitDBuilder.h.

Referenced by build(), getLayer(), and setGeometry().

CSCHitFromStripOnly* CSCRecHitDBuilder::hitsFromStripOnly_

private

The Program first constructs proto wire/strip hits which it stores in a special collection. Proto strip/wire segments are then build from these hits and allow to clean up up the list of hits.

Definition at line 86 of file CSCRecHitDBuilder.h.

Referenced by build(), CSCRecHitDBuilder(), setConditions(), and ~CSCRecHitDBuilder().