d5/d24/TMTrackProducer__cff_8py_source.html

 import FWCore.ParameterSet.Config as cms


 #---------------------------------------------------------------------------------------------------------

 # This describes the full TMTT track reconstruction chain with 3 GeV threshold, where:

 # the GP divides the tracker into 16 eta sectors;

 # the HT uses a  32x16 array followed by 2x2 Mini-HT array, with transverese HT readout & multiplexing,

 # followed by the track fit (KF); and duplicate track removal (Algo1) is run.

 #

 # This usually corresponds to the current firmware.

 #---------------------------------------------------------------------------------------------------------


 #=== TMTT tracking needs to get FE stub window sizes from this.


 from L1Trigger.TrackTrigger.TTStubAlgorithmRegister_cfi import *


 #=== Random number generator for Stub Killer (dead module emulation)


 RandomNumberGeneratorService = cms.Service("RandomNumberGeneratorService",

     TMTrackProducer = cms.PSet(initialSeed = cms.untracked.uint32(12345))

 )


 #=== Import default values for all parameters & define EDProducer.


 from L1Trigger.TrackFindingTMTT.TMTrackProducer_Defaults_cfi import TMTrackProducer_params


 TMTrackProducer = cms.EDProducer('tmtt::TMTrackProducer',

   # Load cfg parameters from TMTrackProducer_Defaults_cfi.py

   TMTrackProducer_params

 )


 #===================================================================================================

 # Uncomment the following 2 lines to enable use of MC truth info & output histograms.

 # (This costs CPU, and is unnecessary if you only care about producing TTTrack collection).

 #===================================================================================================


 #TMTrackProducer.EnableMCtruth = cms.bool(True)

 #TMTrackProducer.EnableHistos  = cms.bool(True)


 #===================================================================================================

 #=== All the following parameters already have identical values in TMTrackProducer_Defaults_cfi .

 #=== They are listed here just to remind you of the most interesting parameters to play with.

 #===================================================================================================


 #--- Configure track fitting


 # Use only 4 parameter helix fit Kalman Filter (which automatically runs on tracks produced with no r-z track filter)

 #TMTrackProducer.TrackFitSettings.TrackFitters = cms.vstring("KF4ParamsComb")


 # Allow KF to assign stubs in up to this many layers to fitted tracks.

 #TMTrackProducer.TrackFitSettings.KalmanMaxNumStubs  = cms.uint32(6)

 # Enable more sophisticated fit mathematics in KF.

 #TMTrackProducer.TrackFitSettings.KalmanHOtilted     = cms.bool(True)

 #TMTrackProducer.TrackFitSettings.KalmanHOhelixExp   = cms.bool(True)

 #TMTrackProducer.TrackFitSettings.KalmanHOalpha      = cms.uint32(2)

 #TMTrackProducer.TrackFitSettings.KalmanHOprojZcorr  = cms.uint32(2)

 #TMTrackProducer.TrackFitSettings.KalmanHOfw      = cms.bool(False)


 #--- Switch off parts of the track reconstruction chain.


 #TMTrackProducer.DupTrkRemoval.DupTrkAlgFit    = cms.uint32(0)

 #TMTrackProducer.TrackFitSettings.TrackFitters = cms.vstring()


 #--- Keep Pt threshold at 3 GeV, with coarse HT, but switch off Mini-HT.


 #TMTrackProducer.HTArraySpecRphi.MiniHTstage         = cms.bool(False)

 #TMTrackProducer.HTFillingRphi.MaxStubsInCell        = cms.uint32(16)

 #TMTrackProducer.HTArraySpecRphi.HoughNbinsPt        = cms.uint32(16)

 #TMTrackProducer.HTArraySpecRphi.HoughNbinsPhi       = cms.uint32(32)

 #TMTrackProducer.HTFillingRphi.BusySectorMbinRanges  = cms.vuint32(2,2,2,2,2,2,2,2)

 #TMTrackProducer.HTFillingRphi.BusySectorMbinOrder   = cms.vuint32(0,8, 1,9, 2,10, 3,11, 4,12, 5,13, 6,14, 7,15)


 #--- Reduce Pt threshold to 2 GeV, with coarse HT, and switch off Mini-HT.


 #TMTrackProducer.HTArraySpecRphi.MiniHTstage        = cms.bool(False)

 #TMTrackProducer.HTFillingRphi.MaxStubsInCell       = cms.uint32(16)

 #TMTrackProducer.HTArraySpecRphi.HoughNbinsPt       = cms.uint32(24)

 #TMTrackProducer.HTArraySpecRphi.HoughNbinsPhi      = cms.uint32(32)

 #TMTrackProducer.GenCuts.GenMinPt                   = cms.double(2.0)

 #TMTrackProducer.HTArraySpecRphi.HoughMinPt         = cms.double(2.0)

 #TMTrackProducer.HTFillingRphi.BusySectorMbinRanges = cms.vuint32(2,2,2,2,2,2,2,2,2,2,2,2)

 #TMTrackProducer.HTFillingRphi.BusySectorMbinOrder  = cms.vuint32(0,12, 1,13, 2,14, 3,15, 4,16, 5,17, 6,18, 7,19, 8,20, 9,21, 10,22, 11,23)


 #--- Reduce Pt threshold to 2 GeV, with coarse HT, followed  by Mini-HT.


 #TMTrackProducer.HTArraySpecRphi.HoughNbinsPt        = cms.uint32(48)

 #TMTrackProducer.HTArraySpecRphi.HoughNbinsPhi       = cms.uint32(64)

 #TMTrackProducer.GenCuts.GenMinPt                    = cms.double(2.0)

 #TMTrackProducer.HTArraySpecRphi.HoughMinPt          = cms.double(2.0)

 #TMTrackProducer.HTArraySpecRphi.MiniHoughMinPt      = cms.double(3.0) # Mini-HT not used below this Pt, to reduce sensitivity to scattering.

 #TMTrackProducer.HTFillingRphi.BusySectorMbinRanges  = cms.vuint32(1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1, 24)

 #TMTrackProducer.HTFillingRphi.BusySectorMbinOrder   = cms.vuint32(0,2,4,6,8,10,12,14,16,18,20,22,24,26,28,30,32,34,36,38,40,42,44,46,1,3,5,7,9,11,13,15,17,19,21,23,25,27,29,31,33,35,37,39,41,43,45,47)


 #--- Additional Mini-HT options to improve electron/displaced tracking.


 # Next 2 lines cause tracks found by 1st stage HT to be output if above specified Pt threshold & mini-HT found no tracks.

 # Improves electron tracking. Setting Pt threshold to 0 improves displaced tracking.

 #TMTrackProducer.HTArraySpecRphi.MiniHoughDontKill   = cms.bool(True)

 #TMTrackProducer.HTArraySpecRphi.MiniHoughDontKillMinPt   = cms.double(8.)

 # Extreme displaced tracking also benefits from following.

 #TMTrackProducer.L1TrackDef.MinStubLayers            = cms.uint32(4)  # HT accepts tracks with >= 4 layers

 #TMTrackProducer.TrackFitSettings.KalmanRemove2PScut = cms.bool(True)

 #To study displaced tracking, include non-prompt particles in efficiency definition.

 #TMTrackProducer.GenCuts.GenMaxVertR                 = cms.double(30.)


 #--- Unusual HT cell shapes


 # Simplify HT MUX to allow easy playing with the number of m bins.

 #TMTrackProducer.HTFillingRphi.BusySectorMbinOrder  = cms.vuint32()


 # Diamond shaped cells: (64,62), (34,32) or (46,44) sized array interesting.

 #TMTrackProducer.HTArraySpecRphi.Shape         = cms.uint32(1)

 #TMTrackProducer.HTArraySpecRphi.HoughNbinsPt  = cms.uint32(38)

 #TMTrackProducer.HTArraySpecRphi.HoughNbinsPhi = cms.uint32(32)


 # Hexagonal shaped cells: (64,42), (50,32) or (56,36) sized array interesting.

 #TMTrackProducer.HTArraySpecRphi.Shape         = cms.uint32(2)

 #TMTrackProducer.HTArraySpecRphi.HoughNbinsPt  = cms.uint32(56)

 #TMTrackProducer.HTArraySpecRphi.HoughNbinsPhi = cms.uint32(32)


 # Brick-wall arranged cells: (64,30) or (66,32) sized array interesting.

 #TMTrackProducer.HTArraySpecRphi.Shape         = cms.uint32(3)

 #TMTrackProducer.HTArraySpecRphi.HoughNbinsPt  = cms.uint32(64)

 #TMTrackProducer.HTArraySpecRphi.HoughNbinsPhi = cms.uint32(27)


 #--- Older cfg giving similar tracking performance with slightly larger resource use.


 #TMTrackProducer.PhiSectors.NumPhiSectors           = cms.uint32(36)

 #TMTrackProducer.EtaSectors.EtaRegions = cms.vdouble(-2.4, -2.0, -1.53, -0.98, -0.37, 0.37, 0.98, 1.53, 2.0, 2.4)

 #TMTrackProducer.EtaSectors.ChosenRofZ              = cms.double(45.)

 #TMTrackProducer.EtaSectors.AllowOver2EtaSecs       = cms.bool(False)

 #TMTrackProducer.HTArraySpecRphi.HoughNbinsPhi      = cms.uint32(32)

 #TMTrackProducer.HTArraySpecRphi.NumSubSecsEta      = cms.uint32(1)


 #--- Stub digitization (switch on/off and/or change defaults).


 #TMTrackProducer.StubDigitize.EnableDigitize  = cms.bool(True)


 #--- Reduce requirement on number of layers a track must have stubs in, either globally or in specific eta regions.


 #TMTrackProducer.L1TrackDef.MinStubLayers       = cms.uint32(4)  # Reduce it globally

 #TMTrackProducer.L1TrackDef.EtaSecsReduceLayers = cms.vuint32(5,12) # barrel-endcap transition region


 #--- If globally reducing number of layers cut, best to also use just one HT output opto-link per m-bin.

 # For 3 GeV threshold with no mini-HT.

 #TMTrackProducer.HTFillingRphi.BusySectorMbinRanges = cms.vuint32(1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1)

 # For 2 GeV threshold with mini-HT.

 #TMTrackProducer.HTFillingRphi.BusySectorMbinRanges = cms.vuint32(1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1, 24)


 #--- Change TP to track matching criteria.


 #TMTrackProducer.GenCuts.GenMinStubLayers               = cms.uint32(4)

 #TMTrackProducer.TrackMatchDef.MinNumMatchLayers        = cms.uint32(4)


 #--- Switch off data truncation due to finite band-width.


 #TMTrackProducer.HTFillingRphi.BusySectorKill       = cms.bool(False)

 #TMTrackProducer.HTFillingRphi.BusyInputSectorKill  = cms.bool(False)


 # Don't order stubs by bend in DTC, such that highest Pt stubs are transmitted first.

 #TMTrackProducer.StubCuts.OrderStubsByBend = cms.bool(False)


 #--- Switch on FPGA-friendly approximation to B parameter in GP - will be used in future GP firmware.

 #--- (used to relate track angle dphi to stub bend)

 #TMTrackProducer.GeometricProc.UseApproxB           = cms.bool(True)

TTStubAlgorithmRegister_cfi